Why doesn't my Wi-Fi reach every room?
Written by Daniel Gélinas, checked against primary sources. Last checked .
The short answer
Wi-Fi is a radio signal that spreads out from your router, and everything in its way soaks some of it up: a cupboard, the floor, thick walls, even a fish tank. By the far room there's little left. Before buying a gadget, move the router: out of the cupboard, up high, in the middle of your home. If a big home still has a dead zone, a mesh system works better than a plug-in extender.
The video
Liz is in the back bedroom with an important video call. The Wi-Fi shows one bar. She's tried everything: the laptop is now balanced on a tower of books, pressed against the window, as high and as close to the glass as it goes.
The call freezes. On her own face. Mid-word, eyes half shut, mouth wide open, for everyone to admire.
“Why doesn't my Wi-Fi reach this room?”
Wi-Fi is a radio
Dan's answer starts with something most people never think about: Wi-Fi is a radio. Your router, the box with the blinking lights, is a tiny radio station, sending its signal out in every direction. Your laptop and phone are the listeners.
And like any radio, the signal gets weaker the farther it travels, and weaker again with every thing it has to get through. The bars on your screen are your device telling you how well it can hear the station.
So the question isn't really “why doesn't it reach?”. It's “what's eating it on the way?”
Follow the signal
Liz's router lives where a lot of routers live: in the hall cupboard. On the floor. Behind the boots.
Now follow the signal from there to the back bedroom:
- The cupboard. Router makers are blunt about this: don't hide the router in a closet, cabinet or cupboard. Enclosed spaces weaken the signal before it's even left.
- The floor. A router sitting on the floor sends a good share of its signal straight down, where the floor soaks it up.
- The walls. Each wall takes a little. Thick walls, brick, concrete and other dense materials take a lot. Metal is worse still.
- The fish tank. Wi-Fi doesn't pass well through water. Fish tanks, washing machines and water heaters all get in its way. (The fish don't mind. Your video call does.)
By the time the signal reaches the back bedroom, one bar is all that's left. That room is what people call a dead zone: a spot in your home where the Wi-Fi is too weak to use.
Before you buy anything, move the router
Liz's first instinct was to buy a Wi-Fi booster. Dan's answer: not yet. The cheapest fix is free, and it's the one the router makers themselves recommend first.
Move the router:
- Out of the cupboard, out of cabinets and from behind the TV. Somewhere in the open.
- Up high, on a shelf or a table, not on the floor.
- In the middle of your home, so the signal spreads evenly instead of half of it going out to the garden or the neighbours. In a two-storey home, a central spot on the ground floor is a good start.
- Away from water and metal, and not right next to the microwave: microwave ovens and cordless phones can interfere with Wi-Fi too.
Your router has to stay connected to wherever your internet comes into the home, so you may not be able to move it far. Even a metre or two out of the cupboard and onto a shelf can make a difference you can measure.
Find your dead zone first
Before and after you move anything, measure. Run our speed test standing right next to the router, then again in each room, especially the one that keeps freezing.
- Next to the router, you see roughly what your internet plan delivers.
- In the far room, you see what's left after the walls, the floor and the fish have had their share.
If the numbers in one room are much lower than next to the router, that's your dead zone. Move the router, then run the test again in that room and compare.
Two networks? The 2.4 and 5 GHz trade-off
Many routers broadcast two kinds of Wi-Fi, and some phones even show them as two network names, one ending in “5G” or “5GHz” (nothing to do with 5G mobile data).
- 2.4 GHz reaches farther and gets through walls and floors better, but it's slower and picks up more interference.
- 5 GHz (and the newer 6 GHz) is faster, but it covers less ground, because it struggles more with walls and floors.
So in a far room, a device may hang on to a weak 5 GHz signal when the slower 2.4 GHz one would actually work better. Many routers now pick the best band for you automatically; if yours shows two networks, try the other one in the dead zone and run the speed test on each.
Still a dead zone? Mesh or extender
If you've moved the router and one room is still struggling, that's when a gadget earns its money. There are two main kinds.
A plug-in extender (sometimes sold as a “booster” or “repeater”) is a small box you plug into a wall socket. It listens to your router and passes the signal on. It suits one weak spot on the same floor. Put it about halfway between the router and the dead zone, not in the dead zone itself: it can only pass on a signal it can hear well.
A mesh system is a set of matching units, usually two or three, that you place around your home. They work together as one Wi-Fi network, so you keep one network name as you walk from room to room. Router makers recommend mesh for bigger homes, several rooms or several floors; Netgear, which sells both, says extenders are “less effective than a mesh system for large spaces”.
We don't recommend any particular brand here. What matters more than the brand is where you put the units, and the same rules apply: in the open, raised up, away from water and metal.
What the video left out
“Full bars, but nothing loads” is a different problem. This page is about weak bars in one room. If your bars are full and nothing loads anywhere, the trouble is past your router: here's how to find it.
A cable beats any radio. For a computer, TV or games console that never moves, a network cable from the router gives you the full speed with no walls in the way. It's not glamorous, but it never has a dead zone.
How much each thing soaks up depends. A thin plasterboard wall barely matters; a thick stone or concrete one can matter a lot. That's why measuring in each room beats guessing.
So walls and water eat Wi-Fi. Get the router out of the cupboard, up high and into the middle of your home before you buy anything. And Liz? She moved hers to a shelf in the hallway. Full bars in the back bedroom. Her face moves again.
What you can do
- Run the speed test next to your router, then in each room, to find your dead zone.
- Move the router out of any cupboard or cabinet, up off the floor, and as close to the middle of your home as its connection allows. Then test again.
- Keep it away from fish tanks, metal and the microwave.
- If your router shows two Wi-Fi networks, try the 2.4 GHz one in the far room.
- Still a dead zone? For one weak room on the same floor, an extender placed halfway. For a bigger home or several floors, a mesh system.
Sources
- Netgear: How to Improve WiFi Signal: Best Router Placement to Maximize Coverage and Performance (netgear.com)
Put the router in a central location, raised off the floor on a shelf or table, not in a corner or against a wall, and don't hide it in a closet, cabinet or cupboard. Fish tanks affect performance. Extenders are “quick and affordable, though less effective than a mesh system for large spaces”.
- Linksys Support: why your router's location matters (article 7864) (support.linksys.com)
Thick walls and dense building materials absorb or block Wi-Fi; a router on the floor sends much of its signal into the floor; Wi-Fi doesn't pass well through water (fish tanks, washing machines, water heaters); enclosed spaces like cabinets weaken it. Put the router somewhere central and visible, raised up.
- TP-Link: How to Improve Your Wi-Fi Signal and Wireless Range (tp-link.com)
Place the router in an elevated, central location; each wall or ceiling reduces the signal, especially ones with metal or dense materials. Microwave ovens and cordless phones interfere. Put an extender about halfway between the router and the weak spot; an extender suits a single weak spot on one floor, mesh suits several rooms or floors.
- Netgear: 2.4 GHz vs 5 GHz vs 6 GHz WiFi Frequency: Which is best? (netgear.com)
2.4 GHz reaches farther but is slower; 5 GHz and 6 GHz are faster but cover less, because higher frequencies have a harder time getting through walls and floors. 2.4 GHz picks up more interference from things like microwaves.
Related questions
- Full Wi-Fi bars, so why is nothing loading?
Full bars, and the movie still won't start? Your Wi-Fi bars only measure the last few steps of the trip. Here's how to find where it's really broken.
More on YouTube
Dan and Liz answer one everyday tech question at a time, most of them in under a minute.